Elcometer 127 Keane-Tator Surface Comparators & Magnifier

The Elcometer 127 Surface Comparators are available in sand, shot or grit surface profiles. Each surface comparator is supplied with 5 profile grades ranging from 0.5 - 5.5mils. Designed for use with the Elcometer 127 illuminated magnifier, each surface comparator has a hole in the centre allowing for clear visual comparisons to be made. 5 Roughness Values per Comparator.

Elcometer 128 Pictorial Surface Standards

Pictorial Surface Standards are high quality photographs which are used for comparison purposes to assess the visual appearance of a steel surface. Elcometer’s range of Surface Standards covers most of those required for surface cleanliness. Surface Standards include: BS EN ISO 8501-1:2007/SIS 055900 BS EN ISO 8501-4:2006 The SSPC Standard - VIS 1 The SSPC Standard - VIS 2 The SSPC Standard - VIS 3 The SSPC Standard - VIS 4 The SSPC Standard - VIS 5

Elcometer 134 CSN Chloride, Sulphate & Nitrate Kit

Designed to accurately, measure surface chloride, sulphate and nitrate ions in minutes, the Elcometer 134 CSN Salt kit offers a single kit solution for testing in the field. All the components of the Elcometer CSN Test Kits are pre-measured and pre-dosed for trouble free testing. Results are recorded in parts per million (ppm) requiring no complicated calculations. Elcometer 134 CSN tests are all designed to use a ratio of 1:1 for easy conversation to µg/cm².Supplied in an ABS plastic carry case for easy portability around the site, each field kit is supplied with full instructions attached to the inside lid, together with: 5 x Chloride tests 5 x Sulphate tests, together with 1 x colorimeter, for sulphate testing 5 x Nitrate test strips 5 x Syringes (without needles) Refill kits containing 5 x chloride, nitrate and sulphate tests are available.

Elcometer 135B Bresle Patches

Elcometer 135B Bresle Patches Elcometer 135B Original Bresle Patches are used to determine surface chloride contamination and are self-adhesive rubber film patches with a sealed compartment for sampling soluble impurities from steel surfaces with a suitable solvent. Elcometer 135B Bresle Patches can also be used with the Elcometer 138C Bresle Salt Kit.

Elcometer 135C Bresle Test Patches

The Elcometer 135C Bresle Test Patch determines the concentration of soluble salts on uncoated surfaces in accordance with the ISO 8502-6 test method.

Elcometer 138 Conductivity Meter

Incorporating a flat sensor, the Elcometer 138 Conductivity Meter can measure the conductivity of a solution from a single drop of a sample. Users can either place a sample on the conductivity meter’s flat sensor or immerse the meter’s sensor directly into the solution under test. The Elcometer 138 Conductivity Meter can be used for a broad range of applications, including: soluble salt concentrations, the electric conductivity (EC) of solutions used in agricultural operations and measuring rainwater pollution levels.

Elcometer 210 Paint Thermometer

The Elcometer 210 Paint Thermometer is used to accurately measure paint temperature. It is often important to ensure the temperature of the paint to be applied is at a temperature which will ensure correct application. The Elcometer 210 Paint Thermometer is supplied with a clip to enable the thermometer to be hooked on to the edge of a paint can allowing accurate temperature measurement of the paint.

Elcometer 142 ISO 8502-3 Dust Tape Test Kit

he Elcometer 142 Dust Tape Test kit allows assessment of the quantity and size of dust particles on surfaces prepared for painting. Dust on blast cleaned surfaces can reduce coating adhesion, leading to premature coating failure and sub-standard coating finish. Used in conjunction with the Elcometer 145 Dust Tape Roller the kit can be used in accordance with the recommendations of BS EN ISO 8502-3 either as a pass/fail test or as a permanent record of the presence of dust.

Elcometer 214L IR Digital Laser Thermometer

The Elcometer 214 is a simple, easy-to-use, non-contact thermometer which safely and accurately measures surface temperature of non-reflective materials using infrared technology. With a user switchable measuring range of -35°C to 365°C or -31°F to 689°F, a digital display of the temperature is produced in less than one second. -Non-contact technology with laser spot indicator -ºC / ºF user switchable -Fast, 1 second scanning of any surface -Measure objects as small as 25mm (1”) -Distance-to-Target Ratio of 8:1 -Easy to read LCD display

Elcometer 510 Automatic Pull-Off Adhesion Gauge

The Elcometer 510 Automatic Pull-Off Adhesion Gauge accurately measures the adhesion strength of coatings on a wide range of substrates.

Elcometer 280 Pulsed DC Holiday Detector

The Elcometer 280 is a ‘stick type’ holiday detector which has been designed to make pulsed DC high voltage holiday detection safer, easier and more reliable than ever before.

Elcometer 147 Weld Gauge

The Elcometer 147 Weld Gauge measures many aspects of welds in both metric and imperial units.

Our Partners

Benny Wu Wijaya Wu Willy Wu