Elcometer 270 Pinhole Detector

The Elcometer 270 range utilises the wet sponge technique and has been designed to set a new standard for wet sponge pinhole detectors - a high quality, low voltage detector with similar accessories to a high voltage spark tester.

Elcometer 3230 Coil Coating Wet Film Wheels

This instrument is similar to the Elcometer 3230 Wet Film Wheel, but is designed for use in the coil coating process.

Elcometer 410 Anemometer

he Elcometer 410 Anemometer is a portable, pocket size instrument for taking accurate readings of wind speed. The lightweight impeller with high precision jewel bearings provides very accurate airflow measurements even at low speeds. The anemometer's impeller can easily be replaced without the need to return the unit to Elcometer. The wind speed can be displayed in various measurement units; indicating current speed, maximum speed or average speed.

Elcometer 236 DC Holiday Detector

The Elcometer 236 Holiday Detector provides high voltage porosity testing to detect pits, flaws, holes, etc. in a wide variety of non-metallic coatings. The Elcometer 236’s convenient carry case allows the probe handle and accessories to be attached to the front making the Elcometer 236 holiday tester ideal for field, site or laboratory inspection.

Elcometer 266 DC Holiday Detector

The Elcometer 266 revolutionises high voltage DC testing of coatings porosity detection making it safer, easier and more reliable than ever before. The Elcometer 266 holiday detector can be used to test porosity on coatings up to 7.5mm (300 mils) thick and is ideal for inspecting coatings on pipelines and other protective coatings. This holiday tester features a built-in voltage calculator which will determine and set the correct test voltage based upon the test standard and the thickness of coating being tested.

Elcometer 506 Pull-Off Adhesion Tester

The Elcometer 506 are lightweight, portable and easy-to-use adhesion testers available in analogue or digital gauges and are suitable for measuring the pull-off adhesion of coatings up to 50MPa (7250psi) either on-site, or in the laboratory. Variasi

Elcometer 3230 Wet Film Wheels

The Elcometer 3230 Wet Film Wheel is a high precision, accurate and easy to use instrument which consists of a set of three wheels. The central wheel is of a smaller diameter and is eccentric relative to the two outer wheels.

Elcometer 3238 Long Edge Wet Film Combs

These stainless steel combs are wire eroded to provide an accuracy ±5% of marked value or ±3μm (0.12mil), whichever is greater, and are supplied with either Metric or Imperial measurements. Each wet film comb has 24 measurement stages (teeth) providing a more accurate wet film thickness value.

Elcometer 7062 MarSurf PS10 Surface Roughness Tester

The Elcometer 7062 surface roughness tester is a light weight and portable measuring solution for the range of surface roughness measurements required for compliance to International Standards. In protective coating applications there is a requirement to measure surface roughness. With 31 surface parameter settings available the Elcometer 7062 surface roughness tester can display all parameters that comply to National & International Standards. These values include peak-to-valley profile measurement in combination with an assessment of the frequency of peaks within the sample area. The Elcometer 7062 surface roughess tester is a light weight and portable measuring solution for the range of surface roughness measurements required for compliance to International Standards. The unit is also suitable for assessing surface roughness conditions in a wide range of general industrial applications; particularly where the sample is too large to bring to the laboratory. *Multi-Lingual Display: All the required information is displayed on screen in a choice of 17 languages. *Flexible: Can be used in virtually any position; horizontally, vertically, upside down. A height adjustment accessory to accommodate various sample sizes is supplied with each gauge as standard. *Integrated Calibration Standard: No external calibration standard is required; provides greater ease of use. *Removable Drive Unit: Drive unit can be removed from main unit and used with an extension cable (included) to allow for measurement in hard to reach areas. *Stylus pick-up with removable protection: 2µm (80µin) diamond stylus tip with a measuring force of 0.7 mN. Different stylus’ are available for various applications.

Elcometer 138-1C Bresle Salt Kit with Elcometer 135C Bresle Patch

It is essential that the level of contaminants on a surface is measured prior to application of the coating to ensure the quality of the coating and that its optimum lifetime is achieved. If the coating is applied to a contaminated surface, which is not properly prepared, it could fail prematurely resulting in costly re-coating and high maintenance costs. The Elcometer 138 Bresle Kits include the Elcometer 138 Bresle Salt Meter. This lightweight, portable meter measures the conductivity of the test sample using a single drop, then automatically converts this to show the density of salts, negating the need for the user to do a manual calculation when working in accordance with ISO 8502-6 or ISO 8502-9. The Elcometer 138B Basic Bresle Kit includes the Elcometer 138E Conductivity Meter. Incorporating a cup-style sensor, the Elcometer 138 Conductivity Meter can measure the conductivity of a solution from a few drops of a sample.

Calibration Foils Sets

The Elcometer 990 coating thickness gauge calibration foils are ideal for use in the laboratory, on the production line or on site. Calibration foils or shims are the most convenient way of creating a coating thickness standard on the substrate material, surface finish or form. Shims provide the ideal method for adjusting the calibration of the coating thickness gauge to ensure the greatest possible accuracy.

Zero Test Plates

Elcometer provides a range of Zero Test Plates to ensure correct calibration of the coating thickness gauge. When used in conjunction with a set of foils, Zero Test Plates are ideal to test a coating thickness gauge’s functionality and calibration, ideal for when it may be difficult or impractical to obtain an uncoated substrate.

Our Partners

Benny Wu Wijaya Wu Willy Wu